PIC18F45K80-I/ML【PDF 45/351 页】MCU PIC 32KB FLASH 44QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3861

41页 42页 43页 44页 [45页]46页 47页 48页 49页

2010-2012 Microchip Technology Inc.

DS39977F-page 139

PIC18F66K80 FAMILY

8.0

DATA EEPROM MEMORY

The data EEPROM is a nonvolatile memory array,

separate from the data RAM and program memory, that

is used for long-term storage of program data. It is not

directly mapped in either the register file or program

memory space, but is indirectly addressed through the

Special Function Registers (SFRs). The EEPROM is

readable and writable during normal operation over the

entire VDD range.

Five SFRs are used to read and write to the data

EEPROM, as well as the program memory. They are:

EECON1

EECON2

EEDATA

EEADR

EEADRH

The data EEPROM allows byte read and write. When

interfacing to the data memory block, EEDATA holds

the 8-bit data for read/write and the EEADRH:EEADR

being accessed.

The EEPROM data memory is rated for high erase/write

cycle endurance. A byte write automatically erases the

location and writes the new data (erase-before-write).

The write time is controlled by an on-chip timer; it will

vary with voltage and temperature, as well as from chip-

to-chip. Please refer to Parameter D122 (Table 31-1 in

Section 31.0 “Electrical Characteristics”

) for exact

limits.

8.1

EEADR and EEADRH Registers

The EEADRH:EEADR register pair is used to address

the data EEPROM for read and write operations.

EEADRH holds the two MSbs of the address; the upper

6 bits are ignored. The 10-bit range of the pair can

address a memory range of 1024 bytes (00h to 3FFh).

8.2

EECON1 and EECON2 Registers

Access to the data EEPROM is controlled by two

registers: EECON1 and EECON2. These are the same

registers which control access to the program memory

and are used in a similar manner for the data

EEPROM.

The EECON1 register (Register 8-1) is the control

bit, EEPGD, determines if the access will be to program

memory or data EEPROM memory. When clear,

operations will access the data EEPROM memory.

When set, program memory is accessed.

Control bit, CFGS, determines if the access will be to

the Configuration registers or to program memory/data

EEPROM memory. When set, subsequent operations

access Configuration registers. When CFGS is clear,

the EEPGD bit selects either program Flash or data

EEPROM memory.

The WREN bit, when set, will allow a write operation.

On power-up, the WREN bit is clear. The WRERR bit is

set in hardware when the WREN bit is set and cleared,

when the internal programming timer expires and the

write operation is complete.

The WR control bit initiates write operations. The bit

cannot be cleared, only set, in software; it is cleared in

hardware at the completion of the write operation.

Control bits, RD and WR, start read and erase/write

operations, respectively. These bits are set by firmware

and cleared by hardware at the completion of the

operation.

The RD bit cannot be set when accessing program

memory (EEPGD = 1). Program memory is read using

table read instructions. See Section 7.1 “Table Reads

and Table Writes”

regarding table reads.

The EECON2 register is not a physical register. It is

used exclusively in the memory write and erase

sequences. Reading EECON2 will read all ‘0’s.

Note:

During normal operation, the WRERR is

read as ‘1’. This can indicate that a write

operation was prematurely terminated by

a Reset, or a write operation was

attempted improperly.

Note:

The EEIF interrupt flag bit (PIR4<6>) is

set when the write is complete. It must be

cleared in software.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式